Question: Can I Connect Two Black Wires Together?

Can you connect two hot wires together?

Okay, and I’m assuming you are talking AC voltage…Only if the two hot wires were from the same phase.

If you take a volt meter and check across the two wires and there’s zero volts, you can put them together..

Why are both black and white wires hot?

like the title says both wires (black and white get or turn hot). To answer your question, Yes, that is correct. The reason you are getting 120 volts when the fan/light is on is because the voltage is feeding trough the motor or the light bulb (or both).

What happens if you connect a positive wire to a negative wire?

If you connect positive to negative directly with a wire, you get a very low resistance circuit. The lower the resistance, the higher the current. The is called a short circuit. … Batteries have internal resistance, so this has to be added to the resistance of the wire.

How do you wire a light with two black wires?

Connect the top screw to the wire that feeds to the light. Connect the bottom screw to the hot wire. When you turn the power back on, and if you want to swap the direction of the switch (as in press down to turn off, or turn on), turn off the power and switch the two black wires.

Can you connect black and white wires together?

Re: White and black wire crossed A single black and white connected together is normal. It is part of a switch loop. A black connected to a group of whites is not normal and probably should be connected to the other blacks. It is normal to have a white connected to a group of blacks if a switch loop is used.

Can Reverse polarity cause a fire?

Watch out: Reversed polarity on an electrical outlet is dangerous. If you accidentally reverse these wires the device you plug in to the receptacle may “work” but it is unsafe and risks a short circuit, shock, or fire.

What if I have two black wires?

Black means hot, white signifies neutral, and green indicates ground. However, if you need to rewire a light switch or a plug socket, you may occasionally come across two black wires. It’s essential that you determine which black wire is hot before proceeding.

What happens if you mix up hot and neutral wires?

This happens when the hot and neutral wires get flipped around at an outlet, or upstream from an outlet. Reversed polarity creates a potential shock hazard, but it’s usually an easy repair. … This wire is commonly referred to as the neutral wire, and it should always be white.

Is the black wire positive or negative?

Positive – The wire for the positive current is red. Negative – The wire for the negative current is black. Ground – The ground wire (if present) will be white or grey.

How do you wire a light with two sets of wires?

Connect the lead wires from the fixture to the black hot wire in the electrical box by twisting a wire connector to the ends of the lead and hot wires. Repeat these connections with the two white neutral wires from the light fixture and the white neutral wire in the light fixture box.

Does it matter where the hot wire goes on a switch?

If your switch has a “LINE” marking, the always hot wire goes to this. The other connection will be “LOAD” where the load (ie light fixture) is wired. The load wire may have red electrical tape on it to differentiate.

How can you tell which wire is hot and which is neutral?

Identify the neutral wire in the fixture by looking at the wires. In most modern fixtures the neutral wire will be white and the hot wire is red or black. In some types of fixtures, both wires will be the same color. In this case, the neutral wire is always identified by some means.

Which wire is positive when both are black?

If the multi-colored wire is black and red, the black wire is the negative wire, while the red one is positive. If both wires are black but one has a white stripe, the striped wire is negative, while the plain black wire is positive. Look in the owner manual to determine which wires are negative in a car.

Why do I have 2 black wires and 2 white wires?

If there is power in both the up and down position of your light switch, than that is the hot power. If the light was fed power first than here is how you connect the wires. Take your black (hot all the time wire) and marrett it onto the white of the opposite cable (that brings hot power down to your switch).

Why are there 2 black wires on light switch?

The bare or green-wrapped ground wires serve as a backup to divert the power safely away in case of an electrical fault. In most cases, two black wires will be attached to the switch’s two terminal screws.

What happens if you wire a light switch backwards?

But here’s the catch: If you connect the circuit wires to the wrong terminals on an outlet, the outlet will still work but the polarity will be backward. When this happens, a lamp, for example, will have its bulb socket sleeve energized rather than the little tab inside the socket.