- What is reference signal power in LTE?
- What is the main reason for open loop power control?
- What are the typical values of LTE cyclic prefix for normal and extended types respectively?
- Why is power control important in CDMA?
- What is the maximum number of CCE possible in LTE?
- What is TPC command in LTE?
- What are the key requirements in uplink power in LTE?
- What is power headroom LTE?
- What is uplink power control?
- What is DRX in LTE?
- What is MAC CE LTE?
- What is control power?
- What is open loop power control?
- How do I turn on power controls?
What is reference signal power in LTE?
In other words RSRP (Reference Signal Receive Power) is the average power of Resource Elements (RE) that carry cell specific Reference Signals (RS) over the entire bandwidth, so RSRP is only measured in the symbols carrying RS.
RSRP is the average received power of a single RS resource element RSRP..
What is the main reason for open loop power control?
Open Loop Power Control is an important technique providing adaptation of user transmit power. There are multiple factors like cell size, interference conditions, etc. that determine the optimal settings of power control (PC) parameters.
What are the typical values of LTE cyclic prefix for normal and extended types respectively?
A Resource Element (RE) is the smallest defined unit which consists of one OFDM sub-carrier during one OFDM symbol interval. Each Resource Block consists of 12 · 7 = 84 Resource Elements in case of normal cyclic prefix (72 for extended CP).
Why is power control important in CDMA?
In CDMA, since all the mobiles transmit at the same frequency, the internal interference of the network plays a critical role in determining network capacity. Further, each mobile transmitter power must be controlled to limit the interference. Power control is essentially needed to solve the near-far problem.
What is the maximum number of CCE possible in LTE?
Common search space :- It consists of CCE’s which are used for sending the control information which is common for all the UE’s . Maximum number of CCE present in common search space is 16.
What is TPC command in LTE?
Once initial PRACH is detected, the UE power is controlled dynamically by TPC (Transmission Power Control) command (MAC CE or TPC field in DCI 0). It means UE Transmission Power is controled by some feedback input from eNB.
What are the key requirements in uplink power in LTE?
It cannot transmit more than its maximum UE power which is commonly 23 dBm for most LTE UEs in the Uplink. The objective of the eNOdeB is that UE should transmit only enough power in the uplink in a range which is the minimum required amount.
What is power headroom LTE?
Power headroom indicates how much transmission power left for a UE to use in addition to the power being used by current transmission. … Since the more resource block the UE is using, the higher UE Tx power gets, but the UE Tx power should not exceed the max power defined in the specification.
What is uplink power control?
The Uplink Power Control System (UPC) is a self-contained, rack-mountable unit designed for geostationary satellite communications systems. It adjusts the strength of uplink signals to compensate for varying weather conditions.
What is DRX in LTE?
LTE: Connected Mode DRX. In LTE, without Discontinuous Reception (DRX), the UE has to be awake all the time in order to decode downlink data, as the data in the downlink may arrive at any time. This means that UE has to be monitoring PDCCH in every subframe in order to check if there is downlink data available.
What is MAC CE LTE?
These special MAC structure carrying the control information is called ‘MAC CE’, which means ‘MAC Control Element’. This special MAC structure is implemented as a special bit string in LCID field of MAC Header (Refer to LTE MAC page for the details of MAC header).
What is control power?
Controlling Power means the effective power used to direct the Company’s activities and to establish the guidelines for the operation of its management bodies, directly or indirectly, in fact or under the law, regardless of the equity interest that is held.
What is open loop power control?
Open Loop Power Control Measurement Description As defined in the 3GPP standard TS 34.122 5.4. 1.3, the open loop power control is the ability of the UE transmitter to sets its output power to a specific value. … The open loop power control measurement can only be initiated with the Trigger Arm to be Single.
How do I turn on power controls?
To get to it you must;Enable developer settings. Go to the Settings app and go to About Phone. … Pull down the Notifications panel and tap and hold the little cog wheel button next to your profile button. … System UI Tuner will now appear as a panel in the Settings app. … Tap Power notification controls and turn it on.